Translation of "translation of lorsqu’un matériau " (French → English) :

(10) If reflective material referred to in S5.1.1.4 of TSD 108 is applied to a non-vertical surface, the entrance angle used to demonstrate that the material conforms to the performance standards prescribed by that section shall be the sum of the entrance angle specified in Table 1 or Table 1A of SAE Standard J594f, Reflex Reflectors (January 1977), and the angle, measured on the horizontal centreline of the material, by which the material deviates from the vertical.

(22) If the retroreflective sheeting referred to in S5.7.1.2 of TSD 108 is applied to a non-vertical surface, the entrance angle used to demonstrate that the sheeting conforms to the photometric requirements prescribed by that section shall be the sum of the entrance angle specified in column 1 of Figure 29 of TSD 108 and the angle, measured at the horizontal centreline of the sheeting, by which the sheeting deviates from the vertical.

11. Where these Regulations require that a particular construction, machinery fitting, appliance, apparatus or material be fitted or carried in a ship or any particular provision to be made in a ship, a pollution prevention officer may allow any other construction, machinery fitting, appliance, apparatus or material to be fitted or carried, or any other provision to be made, if he is satisfied that such other construction, machinery, fitting, appliance, apparatus, material or provision is at least equivalent to that required by these Regulations.

(b) rivets shall be cold-driven, the heads and points bearing on strips, plates or washers of appropriate material with precautions against bimetallic corrosion being taken, a suitable compound shall be used when a watertight joint is required, the rivets shall be dipped in resin or other suitable sealant to seal the exposed fibres in the holes and the minimum distance between the centre of the rivet hole and the edge of the G.R.P. material shall be three times the diameter of the hole;

5. The notified body which issued the European approval for materials shall withdraw that approval if it finds that it should not have been issued or if the type of materials is covered by a harmonised standard.

where the substance contained has been shown not to be harmful to the material from which the pressure equipment is made and no other internal degradation mechanisms are reasonably foreseeable.

in the case of public works contracts the totality of the technical prescriptions contained in particular in the procurement documents, defining the characteristics required of a material, product or supply, so that it fulfils the use for which it is intended by the contracting authority; those characteristics include levels of environmental and climate performance, design for all requirements (including accessibility for disabled persons) and conformity assessment, performance, safety or dimensions, including the procedures concerning quality assurance, terminology, symbols, testing and test methods, packaging, marking and labelling, u ...[+++]ser instructions and production processes and methods at any stage of the life cycle of the works; those characteristics also include rules relating to design and costing, the test, inspection and acceptance conditions for works and methods or techniques of construction and all other technical conditions which the contracting authority is in a position to prescribe, under general or specific regulations, in relation to the finished works and to the materials or parts which they involve;

in the case of works contracts, the totality of the technical prescriptions contained in particular in the procurement documents, defining the characteristics required of a material, product or supply, which permits a material, a product or a supply to be described in a manner such that it fulfils the use for which it is intended by the contracting entity; those characteristics include levels of environmental and climate performance, design for all requirements (including accessibility for disabled persons) and conformity assessment, performance, safety or dimensions, including the procedures concerning quality assurance, terminology, s ...[+++]ymbols, testing and test methods, packaging, marking and labelling, user instructions, and production processes and methods at any stage of the life cycle of the works; those characteristics also include rules relating to design and costing, the test, inspection and acceptance conditions for works and methods or techniques of construction and all other technical conditions which the contracting entity is in a position to prescribe, under general or specific regulations, in relation to the finished works and to the materials or parts which they involve;

(s) ‘co-products’ means raw materials which have a market value or alternative uses and materials that constitute a significant outcome of a process in terms of economic value or where the main process has been deliberately modified to produce a larger quantity or another quality of the material at the expense of the main product; [Am. 71]

When these materials are derived from well-managed forests, they have the ecological characteristic of allowing us to substitute one material for another, in this case steel or concrete, thereby decreasing the ecological and environmental footprint of that material.