Boost Your Productivity!Translate documents (Ms-Word, Ms-Excel, ...) faster and better thanks to artificial intelligence!
https://pro.wordscope.com
https://blog. wordscope .com
Backing plate mounted brake
Bracking plate mounted brakes
Hand brake mounting plate
Hand brake pawl plate

Translation of "Hand brake mounting plate " (English → French) :

TERMINOLOGY
see also In-Context Translations below
hand brake mounting plate

plaque de fixation de frein à main


hand brake mounting plate

plaque de fixation de frein à main


hand brake pawl plate

plaque de cliquet de frein à main


hand brake pawl plate

plaque de cliquet de frein à main


backing plate mounted brake

frein à segments sur plateau


bracking plate mounted brakes

freins à segments montés sur plateau de frein
IN-CONTEXT TRANSLATIONS
(5) Brake shaft shall be arranged with a square fit at its upper end to secure the hand brake wheel; said square fit shall be not less than 7/8 inch square. Square-fit taper; nominally 2 in 12 inches (See Plate A of Schedule II).

(5) Une partie de l’arbre du frein doit être carrée à l’extrémité supérieure de façon à retenir en place la poulie du frein à main; cette partie carrée doit avoir au moins 7/8 de pouce de côté et avoir une section décroissante de 2 pouces par 12 pouces (voir la planche A de l’annexe II).


(2) The hand brake may be of any efficient design, but shall provide the same degree of safety as the design shown on Plate A of Schedule II.

(2) Le frein à main peut être de n’importe quel modèle efficace, mais il doit assurer le même degré de sécurité que le modèle montré à la planche A de l’annexe II.


3.7.3. The make and type of each brake lining or pad shall be visible when the lining or pad is mounted on the brake shoe or back plate in a legible and indelible manner.

3.7.3. La marque et le type de chaque garniture ou plaquette de frein doivent être visibles lorsque celle-ci est montée sur la mâchoire ou plaquette et doivent être inscrits de façon lisible et indélébile.


1.1.1. The vehicle shall be in its normal ride attitude and shall be either securely mounted on raised supports or at rest on a flat surface with the hand brake on.

1.1.1. Le véhicule se trouve dans son assiette normale; il est soit solidement fixé sur des supports surélevés, soit au repos sur une surface plane, le frein à main tiré.


For more results, go to https://pro.wordscope.com to translate your documents with Wordscope Pro!
The requirements of point 5.3.2.3 shall not apply to floor-mounted hand brake control ; for such controls if the height of any part in the released position is above a horizontal plane passing through the lowest H point of the front seats (see Annex IV) the control shall have a cross sectional area of at least 6 75 cm2, measured in a horizontal plane, not more than 6 75 mm from the furthest projecting part (mea ...[+++]

Les prescriptions du point 5.3.2.3 ne s'appliquent pas à la commande du frein à main monté au plancher ; pour de telles commandes, si une quelconque de leurs parties en position de repos dépasse le plan horizontal passant par le point H le plus bas des sièges avant (voir annexe IV), la commande doit avoir une surface d'au moins 6,5 cm2 mesurée dans un plan horizontal situé à une distance ne dépassant pas 6,5 mm de la partie la plus en saillie (mesurée selon la direction verticale).


5.2.2. The hand-brake control, if mounted on or under the instrument panel, shall be so placed that, when it is released, there is no possibility of occupants of the vehicle's contacting it in the event of a frontal impact.

5.2.2. La commande du frein à main, lorsqu'elle est placée sur le tableau de bord ou sous celui-ci, doit être aménagée de façon que, lorsqu'elle se trouve en position de repos, il ne soit pas possible de la heurter en cas de choc frontal.




datacenter (1): www.wordscope.ca (v4.0.br)

'Hand brake mounting plate' ->

Date index: 2022-04-30
w