Boost Your Productivity!Translate documents (Ms-Word, Ms-Excel, ...) faster and better thanks to artificial intelligence!
https://pro.wordscope.com
https://blog. wordscope .com
3-point bend test
3-point bending test
4-point bend test
4-point bending test
Alternate bend test
Assess the visual impact of displays
Assess visual impact of displays
Bending test under third-point loading
Bending test under two-point loading
Compression buckling test
Face bend test
Four-point bend test
Four-point bending test
Impact bending test
Judge visual impact of displays
Normal bend test
Repeated notched-bar impact bending test
Reversed bend test
Test visual impact of displays
Three-point bend test
Three-point bending test

Traduction de «Impact bending test » (Anglais → Français) :

TERMINOLOGIE
voir aussi les traductions en contexte ci-dessous




compression buckling test | impact bending test

essai à choc de flexion | essai de flexion au choc


repeated notched-bar impact bending test

essai de fatigue par choc sur barreau entail


three-point bending test [ 3-point bending test | three-point bend test | 3-point bend test ]

essai de flexion trois points [ essai de flexion 3 points ]


four-point bending test [ 4-point bending test | four-point bend test | 4-point bend test ]

essai de flexion quatre points [ essai de flexion 4 points ]


reversed bend test | alternate bend test

essai de pliage alterné


bending test under third-point loading | bending test under two-point loading

essai sous moment constant


face bend test | normal bend test

essai de pliage à l'endroit


assess the visual impact of displays | judge visual impact of displays | assess visual impact of displays | test visual impact of displays

évaluer l'effet visuel d’étalages
TRADUCTIONS EN CONTEXTE
(b) tested for impact at -35°C and bending at -40°C in accordance with Canadian Standards Association Standard C22.2 No. 0. 3-M1985, Test Methods for Electrical Wires and Cables.

b) soumis à un essai d’impact à -35 °C et de flexion à -40 °C conformément à la norme C22.2 No. 0. 3-M1985 de l’Association canadienne de normalisation intitulée Méthodes d’essai des fils et câbles électriques.


(b) tested for impact at -35 °C and bending at -40 °C in accordance with Canadian Standards Association Standard C22.2 No. 0. 3-M1985, Test Methods for Electrical Wires and Cables.

b) soumis à un essai d’impact à -35 °C et de flexion à -40 °C conformément à la norme C22.2 No. 0. 3-M1985 de l’Association canadienne de normalisation intitulée Méthodes d’essai des fils et câbles électriques.


The instantaneous sum of the impact forces with respect to time shall not exceed 9,4 kN and the bending moment on the test impactor shall not exceed 640 Nm.

La somme instantanée des forces d’impact en fonction du temps ne dépasse pas 9,4 kN et le moment de flexion sur l’élément de frappe de l’essai ne dépasse pas 640 Nm.


The values for the instantaneous sum of the impact forces and the bending moment on the test impactor shall be recorded.

Les valeurs pour la somme instantanée des forces d’impact et le moment de flexion sur l’élément de frappe sont enregistrées.


For more results, go to https://pro.wordscope.com to translate your documents with Wordscope Pro!
The instantaneous sum of the impact forces with respect to time shall be compared with a possible maximum of 5,0 kN and the bending moment on the test impactor shall be compared with a possible maximum of 300 Nm.

La somme instantanée des forces d’impact à un moment donné est comparée à un maximum possible de 5,0 kN et le moment de flexion sur l’élément de frappe de l’essai est comparé à un maximum possible de 300 Nm.


The instantaneous sum of the impact forces with respect to time shall not exceed 7,5 kN and the bending moment on the test impactor shall not exceed 510 Nm.

La somme instantanée des forces d’impact à un moment donné ne dépasse pas 7,5 kN et le moment de flexion sur l’élément de frappe de l’essai ne dépasse pas 510 Nm.


The instantaneous sum of the impact forces with respect to time should not exceed a possible target of 5,0 kN and the bending moment on the test impactor shall be recorded and compared with the possible target of 300 Nm.

La somme instantanée des forces d’impact à un moment donné ne devrait pas dépasser une valeur cible possible de 5,0 kN, et le moment de flexion sur l’élément de frappe de l’essai est enregistré et comparé à la valeur cible possible de 300 Nm.


3.1.2. Upper Legform to Frontal Protection System. The test is performed at an impact speed of 40 km/h. The instantaneous sum of the impact forces with respect to time shall not exceed 7.5 kN and the bending moment on the test impactor shall not exceed 510 Nm.

3.1.2. Collision de haut de jambe factice sur le système de protection frontale: cet essai est effectué à une vitesse d'impact de 40 km/h; la somme instantanée des forces d'impact à un moment donné ne dépasse pas 7,5 kN et le moment de flexion sur l'élément de frappe ne dépasse pas 510 Nm .


This test is carried out at an impact speed of 40 km/h.The maximum dynamic knee bending angle shall not exceed 15.0°, the maximum dynamic knee shearing displacement shall not exceed 6.0 mm, and the acceleration measured at the upper end of the tibia shall not exceed 150 g. This test may be substituted by the Upper Legform to Frontal Protection System “Bumper” test under specified conditions.

L'angle maximal de flexion dynamique du genou ne dépasse pas 15,0°, le déplacement dynamique maximal en cisaillement du genou ne dépasse pas 6,0 mm et l'accélération mesurée à l'extrémité supérieure du tibia ne dépasse pas 150 g. Cet essai peut être remplacé par le test de collision de haut de jambe factice sur le pare-chocs du système de protection frontale aux conditions indiquées.


This test is carried out at an impact speed of up to 40 km/h.The instantaneous sum of the impact forces with respect to time, to the top and the bottom of the impactor, should not exceed a possible target of 5.0 kN and the bending moment on the impactor should not exceed a possible target of 300 Nm .

La somme instantanée des forces d'impact à un moment donné, au sommet et au bas de l'élément de frappe, ne devrait pas dépasser un éventuel objectif de 5,0 kN et le moment de flexion sur l'élément de frappe ne devrait pas dépasser un éventuel objectif de 300 Nm.


w